Flashcal and Flashpaq for 2022 Jeep Wrangler and Gladiator 3.6 Available Now!

This page is all about Flashpaq, Flashcal, and Amp’D 2.0 for ’22 Jeep.

CLICK HERE for info about TD3 on ’22 Jeep

Flashpaq

Superchips offers the easiest and most cost-effective solution to your new Jeep Wrangler or Gladiator’s performance needs by adding it to the Flashpaq’s tuning support. With the ability to add up to 22 horsepower and 21  lb.-ft. torque with 93 octane fuel, the Flashpaq has been specifically calibrated to enhance the driving experience in your vehicle with no engine modifications.  Flashpaq contains tuning for the engine, as well as all the Quick Options features of Flashcal (listed below).  The Flashpaq kit for Jeep Wrangler JL and Gladiator JT also includes a PCM Swap, which means the cost of unlocking your vehicle’s PCM is included in the its price.

IMPORTANT NOTES ABOUT PCM TYPES BEFORE ORDERING:

Currently, only GPEC2A controllers are supported by the TrailDash 3.

 

Jeeps with the GPEC5 the engine control module (PCM) that may come in any variation of Wrangler or Gladiator, eTorque or non-eTorque are currently not supported for tuning, but are supported for BCM (lighting, speedometer for tires, etc) with Flashcal 3571-JL.

Tune for Power and Efficiency, On and Off-Road

Whether you’re hitting a trail off-road, looking for better fuel mileage on your daily commute, or simply need a boost to all-out acceleration and performance, Flashpaq has you covered. The device comes preloaded with performance tunes for 93 and 91 octane fuel for the best power and efficiency (MPG), and a 91 octane compatible Crawl Tune.  Our purpose-built Crawl tune has a recalibrated throttle curve (controlling the engine response to pedal input) that is linear, for precise modulation while easing over steep obstacles at low speeds.  While the performance tunes do improve mileage, especially around town, the MileageXS tune will squeeze every bit possible from a gallon on long highway trips.

Expansive Adjustment Options for the whole Jeep

Flashpaq and Flashcal (below) have always had the commonly available adjustable options, like re-calibrating the speedometer for changes to tire size and axle gear ratio.  Thanks to advancements to the vehicles themselves, and the extensive research of our calibrators, a host of useful “Quick Options” have been added.  Items in the Quick Options list below are available in both Flashpaq and Flashcal, and take seconds to apply because they do not require a reflash of the PCM (engine control module).

Easy Prep for PCM Modification

Tuning any Jeep vehicle built in 2015 or later requires a PCM unlock to allow reading and writing of files, but Superchips has made this step as painless as possible with the included PCM swap.  When you take delivery of your new Flashcal kit, submit this form and we will send an unlocked PCM up front for quick installation and no vehicle down time:  

PCM Cross Ship

A prepaid return shipping label will be included to send your original PCM back as a core trade-in.

 

Tuning Specs

Tune Name                                                         Octane    HP       TQ

Superchips Tune (dyno chart below)        93             22       21

Performance 91                                                  91              20        19

MileageXS SAVE                                                87              N/A    N/A

Crawl                                                                      87              12         14

 

Optional User Adjustments to engine tuning:

  • Adjustable Rev Limiter, adds +258 RPM to stock setting
  • Auto start/stop Disable
  • Speed Limiter Control, Raised

 

Shop Flashpaq 3876-JL

Flashpaq for Jeep®

 

Speedometer and Accessory Calibration for Wrangler and Gladiator

Flashcal

Tire and wheel upgrades are common with Jeep vehicles in general, and Superchips offers the easiest, most cost-effective solution for Wrangler owners to correct a speedometer reading for changes to tire height or axle ratio.  The Flashcal plugs into the truck’s diagnostic port and the user only has to input their new tire size and/or gear ratio changes to return the speedometer to an accurate calibration.  The adjustment can be completed in minutes, and you’ll rest assured your speedometer and odometer are displaying accurately to keep your time on the highway safe and legal!

In addition to speedometer calibration, Flashcal also offers numerous customizations to your vehicle’s features not typically available to the end user, such as setting the TPMS warning threshold or disabling it altogether for off-road use, customized fog light control, auto start/stop disabler, sway bar system control, and much more.

NOTE: Flashcal does not require a PCM swap or modification.   However, a Gateway Bypass Module (included in all kits for this application) must be installed while any adjustment or tuning is being performed on this vehicle.  

See Quick Options list below for all available settings.

Shop Flashcal 3571-JL Here 

 

Quick Options Available on Flashpaq and Flashcal:

 

• Engine Idle Up: 700 – 2000 RPM
• Sway Bar Disconnect in 2Hi (up to 25 MPH)**
• Line Lock- holds brakes on front tires only
• Rock Lock- holds all 4 wheels with brakes for crawling
• Axle Gear Calibration: 2.73 – 5.38
• Tire Size Calibration by height: 25” – 40”
• Transfer Case Gear ratio calibration: 2.72 – 5.00
• TPMS Warning Threshold adjust: 22 – 56 psi.
• TPMS Disable, for aftermarket wheels and no sensors
• Daytime Running Lights Operation: Always On, Selectable, or No DRL
• DRL Location Selector: Fog, Fender, Running, High, Low, Turn, or No DRL
• DRL Dropout Disable, keeps DRL on when using turn signal
• Fog Lights Dropout Disable, for simultaneous use of high beams and fog lights
• Halo Lights Enable or Disable
• One Touch Lane Change Enable, one tap of switch triggers 3 blinks
• Seat Belt Minder Disable, stops chime
• Travel Link Weather Warning Disable
• Splash Screen select: Sport, Sahara, Rubicon
• Headlight Selector: Standard, LED, Front Turn, Tail Lights, 3rd Brake Light
• Auto Start/Stop Disable
• Auxiliary Switches Enable, to add extra factory Aux switches*
• Blind Spot Detection Disable, or Enable to add if not equipped*
• Factory Fog Light Switch Enable, adds controls if not equipped*
• Towing Package Enable, adds controls if not originally equipped*
• Backup Camera Disable, or Enable to add one if not originally equipped*
• Cargo Camera Disable, or Enable to add one if not originally equipped*
• Sway Bar System Disable, for aftermarket or deleted bar*
• Electronic Steering Pump Disable, for conversion to hydraulic system*
• Axle Lockers Disable Rear Only, for conversion to manual*
• Axle Lockers Front & Rear, for conversion to manual*
• Front Axle Disconnect Disable, for removing electronic system (FAD)*

*Our devices reconfigure vehicle controls for this associated change, but additional OEM or aftermarket parts are required to complete the conversion.

**Applies to Rubicon models only

*NOTE: A Gateway Bypass Module (included in kit) must be installed while any adjustment or tuning is being performed on your Jeep JL or Gladiator with Flaschal and Flashpaq.

Instant Throttle Response on your Jeep Wrangler or Gladiator

Amp’D 2.0

A frequent inquiry we get in the field is how to reduce or eliminate the lag in pedal response after certain modifications, like bigger tires.  This can often be a complaint with completely unmodified Jeeps!

Superchips Amp’D 2.0L Throttle Sensitivity Booster is easy to install and delivers immediate improvement to the engine’s throttle response. This increased sensitivity optimizes your Wrangler’s driving experience and puts the power to the ground faster!  Amp’d 2.0 offers an elegantly simple solution that generates “seat of the pants” response you won’t find anywhere else.

Amp’d 2.0 (5) preset throttle settings that can be switched on the fly, and an intuitive plug-and-play installation to factory connectors without cutting or splicing wires.  Settings are adjustable through our wireless switch, or the all-new Amp’d 2.0 smartphone app which includes an option to create custom pedal map curves.

Shop AMP’D 2.0 48868-JL2 HERE

 

 

 

Calibrate & Add Instant Throttle Response Together

Amp’D 2.0 + Flashcal

While Flashpaq does offer solid power improvements, some Jeep JL/JT owners wish to tighten up pedal response and recalibrate specific accessories without completely reprograming the engine control. Combining an Amp’D 2.0 Throttle Booster and Flashcal will fill that void, with a relatively small output of money and time.

The pairing of Flashcal and Amp’D 2.0 Throttle Booster make for an easy install, and reward on investment that few other modifications can match.

Shop Kit 3571-JLA2 HERE

 

 

2022 Wrangler and Gladiator 3.6 is Now Supported by TD3!

TD3 NOW SUPPORTS JEEP WRANGLER AND GLADIATOR 3.6

If you’re looking for tuning, monitoring, and on-the-fly controls, the TrailDash 3 is Superchips’ most versatile device.  TD3’s preloaded tunes include the option to enhance the 3.6’s peak power by as much as 22 hp and 21 lb-ft of torque with the 93 octane Superchips Tune, as well as one for 91 octane fuel, the MileageXS tune to maximize MPG, and the Crawl tune for real off-roading. Our purpose-built Crawl tune features a recalibrated throttle curve (controlling the engine response to pedal input) that is linear, for precise modulation while easing over steep obstacles at low speeds.  While the performance tunes do improve mileage, especially around town, the MileageXS tune will squeeze every bit possible from a gallon on long highway trips.

TD3 uses a 5″ high-definition screen with upgraded processor for fast reading and writing to load performance programs, and boasts a high refresh rate ensuring smooth animation for the customizable virtual gauge display.  The recommended software for updating is available for Window and Mac computer, but contains Wi-Fi capability when there is no computer access.

Tuning any Jeep vehicle built in 2015 or later requires a PCM unlock to allow reading and writing of files, but Superchips has made this step as painless as possible with the included PCM swap.  When you take delivery of your new TD3 kit, submit this form and we will send an unlocked PCM up front for quick installation and no vehicle down time:  

PCM Cross Ship

A prepaid return shipping label will be included to send your original PCM back as a core trade-in.

 

NOTE: A Gateway Bypass Module (included in kit) must be installed while any adjustment or tuning is being performed on your Jeep JL or Gladiator.

IMPORTANT NOTES ABOUT PCM TYPES BEFORE ORDERING:

Currently, only GPEC2A controllers are supported by the TrailDash 3.

Jeeps with the GPEC5 the engine control module (PCM) that may come in any variation of Wrangler or Gladiator, eTorque or non-eTorque are currently not supported for tuning, but are supported for BCM (lighting, speedometer for tires, etc.) by the Flashcal 3571-JL.

 

 

Tune Name                                             Octane    HP       TQ

Superchips Tune (dyno chart below)       93       22       21

Performance 91                                                 91       20       19

MileageXS SAVE                                               87       N/A     N/A

Crawl                                                                     87        12       14

 

Optional User Adjustments to engine tuning:

  • Speed Limiter, Raised
  • Speed Limit in 4×4 Lo, Raised
  • Throttle Booster-20%/+20% sensitivity over stock or base Superchips tune
  • Electric Fan Control by Target Temp, 150-230 degrees F
  • Idle Speed, +/- 400 RPM from stock
  • Rev Limiter in Drive, lower 900 or raise 200 from stock
  • Rev Limiter in Neutral,  +/-600 RPM from stock
  • Fuel enrichment at WOT(Wide Open Throttle),  20% leaner or richer than stock or selected Superchips tune, 1K-7K RPM
  • Mean Brake Torque (MBT) Spark at WOT, +/-10 deg. over stock or base Superchips tune, in 1K-7K RPM
  • Spark Advance at WOT, +/-10 deg. over stock or selected Superchips tune, in 1K-7K RPM
  • MDS Disable

 

Quick Options (changes that can be made without reloading a tune):

 

  • DRL Mode Selector: Headlight in High or Low/Turn Signal/Fog/Euro-Fender
  • Traction Control Disable
  • Factory Fog Light Switch Enable, adds to existing controls if not originally equipped*
  • High Beam Fog Lights Cutout Disable, allows simultaneous use of fog lights and high beams
  • One Touch Turn Signal Enable, one tap triggers 3 blink signal
  • Sway Bar Module Disable, for aftermarket or deleted bar*
  • TPMS Thresholds, Front and Rear axles independent, in 10-56 psi.
  • Speedometer calibration, Tire Height, 20-44”
  • Speedometer calibration, Axle Gear Ratio 2.56 – 5.00

 

*Our devices reconfigure vehicle controls for this associated change, but additional OEM or aftermarket parts are required to complete the conversion.

 

 

This article at Holley’s Motor Life gives a complete description of EAS, TrailDash 3’s customizable switch and auxiliary sensor controls

See more info about TrailDash 3’s live monitoring and Crawl Screen

Shop for TrailDash 3 kit #42051-JL-3

 

Duramax L5P Tuning, with NO ECM SEND-IN!

Flashpaq 2848-DS for 2017-2019 Duramax L5P with In-Field ECM Unlock Cable

We’ve been tuning the 2017-2019 L5P with great power increases for about two years, but this will still be big news for anyone who owns one.  2017-2019 L5P GM Duramax Flashpaq performance programmer (PN 2848-DS) now includes hardware and software to UNLOCK THE ECM IN THE FIELD, which means it is not necessary to remove the ECM from the vehicle and send it in.  This also means we can tune your truck in minutes, with NO VEHICLE DOWNTIME. As always, our device comes preloaded with tunes for various purposes, from performance, towing, or better fuel economy, and the Flashpaq for L5P can add up to 150 horsepower and 350 ft-lbs. of torque without ever turning a wrench. It has never been easier to add real power to an L5P Duramax!

NOTE: Each Flashpaq kit will only be capable of unlocking one vehicle.

 

Tune File Name                        HP            TQ

Heavy Tow                              75              150

MileageXS                              100             200

Tow Performance                125             250

Performance                          150             350

 

 Optional Adjustments With Tuning

  • Rev Limiter, Raise
  • Speed Limiter Disable
  • Adjust Throttle Sensitivity, +5 to +50% over stock
  • Tire Size Speedo Calibration 26”-38”
  • Gear Ratio Calibration, 3.42-5.15:1
  • Idle Speed PARK/Neutral +/- 400 RPM
  • Remember Last Button Setting – Tow/Haul and Exhaust Brake Enable

 

Quick Options (Reflash of ECM tune not required)

  • Temporary idle up for winch/elec. Accessories, 600-1800 RPM
  • Allison Transmission Relearn
  • Manual and Mobile DPF Regen
  • Independent Adjustment of TPMS Threshold for Front & Rear Axles, 1-90psi

Additional Features

  • Kit includes wiring harness and software to unlock vehicle ECM with NO SEND-IN REQUIRED
  • Color screen and user-friendly menus for painless programming
  • Easy updates with our software and any Mac or Windows PC
  • Vehicle parameter monitoring capabilities and Advanced Data Acquisition (PIDs)
  • Reads & clears trouble codes (CELs)
  • Tunes are compatible with other performance upgrades

 

ECM Unlock Instructions: Unlock_Cable_Installation_L5P_17-19_brandless

CLICK HERE TO BUY NOW

 

CLICK HERE FOR MORE USEFUL INFO ABOUT TUNING THE ’17-’19 L5P

 

 

 

 

Flashcal+ (“Flashcal Plus”) for Jeep: Our Newest Device is WIRELESS!

The all-new Flashcal+ (“Flashcal Plus”) is the amazing combination of vehicle configuration tool and calibrator and like you’re used to with the original Flashcal, with live and on-the-fly controls, data streaming displayed as customizable virtual gauges, and code scanner.  Through our newly developed FC+ app (supporting Android and iOS) we can link the processing capability of a modern smartphone to our wireless Bluetooth module for outstanding functionality. 

CLICK HERE for a Full Overview of Flashcal+’s Exciting New Functions

Flashcal+ is Launching with Full Support for Wrangler JK 3.8L/3.6L, Wrangler JL 3.6L/2.0T, and Gladiator 3.6L 

Vehicle Specific Features: Wrangler JK (2007-2018)

  • Corrects speedometer for tire upgrades between 26”- 42”, using GPS-powered Tire Size Wizard or by measured height

  • Speedometer recalibration for axle gear and T-case ratio, 2.73-5.38:1

  • Axle Lock Rear w/ T-case in 4-Hi & 4-Low (CRAWL Screen, JK Rubicon only)

  • Axle Lock Front & Rear w/ T-case in 4-Hi & 4-Low (CRAWL Screen, 3.8L JK Rubicon only)

  • Engine idle up for winching, temporarily with CRAWL Screen, 500-2000 RPM

  • Daytime Running Light Location: Halo, Fender, Fog, High, Low, Turn Signal

  • Daytime running light Enable/Disable

  • One touch lane change

  • TPMS Disable, while using CRAWL Screen or completely for use with aftermarket wheels

  • TPMS Threshold adjust 22-56 psi.

CLICK HERE 

 TO SHOP FOR FLASHCAL+ 3581

 

CLICK to TRY FLASHCAL+ APP FOR YOURSELF IN DEMO MODE

IT’S FREE!

 

Vehicle Specific Features: Wrangler JL (’18-’21) and Gladiator

  • Engine idle up for winching, temporarily with CRAWL Screen, 500-2000 RPM

  • Sway Bar Disconnect in 2Hi, up to 25 MPH (CRAWL Screen, Rubicon only)

  • Line Lock- holds brakes on front tires only

  • Rock Lock- holds all 4 wheels with brakes for crawling

  • Axle Gear Calibration: 2.73 – 5.38:1

  • Tire Size Calibration by height: 26” – 40”

  • Transfer Case Gear ratio calibration: 2.72 – 5.00:1

  • TPMS Warning Threshold adjust: 22–56 psi.

  • TPMS Disable, for aftermarket wheels and no sensors

  • TPMS Off/On (Crawl Screen)

  • Daytime Running Lights Operation: Always On, Selectable, or No DRL

  • DRL Location Selector: Fog, Fender, Running, High, Low, Turn, or No DRL

  • DRL Dropout Disable, keeps DRL on when using turn signal

  • Fog Lights Dropout Disable, for simultaneous use of high beams and fog lights

  • Halo Lights Enable or Disable

  • One Touch Lane Change Enable

  • Dashboard Splash Screen select: Rubicon, Sahara, Sport

  • Seat Belt Minder Disable, stops chime

  • Travel Link Weather Warning Disable

  • Lighting Config, selects Standard or LED: Front Turn, Tail Lights, 3rd Brake Light

  • Auto Start/Stop Disable

  • Auxiliary Switches Enable, to add extra factory Aux switches*

  • Blind Spot Detection Disable, or Enable to add if not equipped*

  • Factory Fog Light Switch Enable, adds controls if not equipped*

  • Towing Package Enable, adds controls if not originally equipped*

  • Backup Camera Disable, or Enable adds if not originally equipped (2018-2020 JL Only) *

  • Cargo Camera Disable or Enable adds if not originally equipped (2018-2020 JL Only) *

  • Electronic Steering Pump Disable, for conversion to hydraulic system*

  • Axle Lockers Disable Rear Only, OR Front and Rear for conversion to manual*

  • Axle Lock Rear OR Front and Rear w/ T-case in 4-Hi & 4-Low (CRAWL Screen, Rubicon Only)

*Our devices reconfigure vehicle controls for this associated change, but additional OEM or aftermarket parts are required to complete the conversion.

 

                                          Bypass

      Gateway Bypass Module (included in all kits for this application) must be installed while any adjustment or tuning is being performed on this vehicle.

Important Notes:

 -3.0 EcoDiesel and right-hand drive model Jeeps are not currently supported

-Most adjustments FC+ applies to your Jeep do not require the dongle TO be left plugged in to remain as selected by user

-Auto Start/Stop disable requires the dongle be left connected to keep system off between key cycles

-Settings entered in CRAWL only remain as entered with dongle plugged in and FC+ App running.

CLICK HERE

TO SHOP FOR FLASHCAL+ 3581-JL (Wrangler JL)

CLICK HERE

TO SHOP FOR FLASHCAL+ 3581-JT (Gladiator)

Flashcal for full-size Bronco 2.3/2.7

 

The Flashcal 1546 is the easiest, and by far the most budget-friendly, way to unlock numerous features not available on Ford’s new Bronco from the factory, and still offers the classic adjustments like speedometer correction.  SKU 1546 supports both 2.3 and 2.7 engines, manual or automatic.

          • Speedometer adjust for Tire Size 28.25 – 36.75”

          • Fog Lights: enable “Bambi Mode” for simultaneous use of fog lights with high-beams

          • Headlamps Position Setting: option for headlamps to return to “Auto Lamps” or remain at last known position

          • Auto Lights Delay: duration headlights illuminate after driver exit, 0, 5, 10, 20, 60, or 120 s.

          • Daytime Running Light disable or enable

          • TPMS Disable, for off-road wheels and tires

          • Independent TPMS threshold: Front and rear axles can be set differently from 1– 90 psi. 

          • Auto Start/Stop Disable: Remains off with every restart, and can be reenabled with the Flashcal any time

          • Silent Mode: Turns off most cabin and exterior lights, and door chime with open door, ignition chime remains

          • Honk Warning Disable: 2-honk warning when driver exits running vehicle with key fob

          • Lock Feedback Lights: Enables hazard blink with unlock command

          • Auto Unlock: Vehicle unlocks with ignition off

          • Auto Lock: Disables factory setting to lock doors when vehicle is in motion

          • Auto Relock: Disables factory setting to re-lock doors 45 seconds after unlocking

          • Remote Unlock: Option to trigger all doors or just driver door

          • Remote Start: Selects engine run time duration for 0, 5, 10, 15 mins

CLICK HERE TO BUY NOW

 

Don’t forget that the new Flashcal 1546 pairs perfectly with the Amp’D 2.0 for better throttle response!

CLICK HERE FOR MORE INFO ON AMP’D 

 

 

Ram DT (New Body) Calibration and Tuning, Now including 2022!

 

The specs and products below also apply to all ‘DT’ chassis Rams that began production in 2019!

2022 Ram DT (New Body) 5.7 is now added for tuning on the Flashpaq 3846-S1 and Dashpaq+ 30627-S1, as well as Quick Option calibration on Flashcal #3545-S1.  The ‘DT’ chassis rams have a large amount of potential power, better economy, and room for customization locked inside them, and Superchips is here with the key.  

Important points 

  • With the 93 octane tune and proper fuel 0-60 mph times dropped by two tenths, from 6.93 to 6.73 after programming. 

  • Our tune files feature revised throttle maps that have been optimized for a better driving experience.

  • The Flashcal is the easiest, and by far the most budget-friendly, way to calibrate for modifications like taller tires, new axle gears, and off-road wheels without TPMS sensors.

  • The two 2022 Ram body styles can be identified by their headlights:

 

Ram DT New Body

 

Ram DS Classic Body (Stay tuned for coverage!)

 

Preloaded Tunes in Flashpaq and Dashpaq+

Ram 1500 eTorque                  Tune                         Min. Octane       HP           TQ

                                                    Superchips Tune                       93         29           37

                                                    Performance 91                         91         25           29

                                                   Tow                                                 91         17           18

                                                    Performance 87                         87         17           17  

                                                       Mileage XS                                   87          N/A      N/A

 

Ram 1500 non-eTorque               Tune                    Min. Octane       HP           TQ

                                                    Superchips Tune                        93          33         28

                                                      Performance 91                           91           26          22

                                                      Tow                                                  91            8            10

                                                       Performance 87                          87            8           10 

                                                        Mileage XS                                    87          N/A      N/A

 

 

Flashpaq and Flashcal

Optional Controls

CLICK HERE TO BUY FLASHCAL 3545-S1

          Parameter                                               Range (where applicable)

  • Engine Idle Up                                                    700 – 2000 RPM

  • Line Lock, holds brakes on front tires only

  • Axle Gear Calibration:                                     3.21-4.88

  • Tire Size by height:                                            25” – 40”

  • Transfer Case Ratio:                                         72 – 5.00

  • TPMS Warning Threshold                              22 – 56 psi.

  • TPMS Disable

 

Flashpaq Only (includes all tunes above for both engines)

CLICK HERE TO BUY FLASHPAQ 3846-S1

          Parameter                                                Range (where applicable)

  • Rev Limiter                                                           Superchips Value / +250 / +500

  • Speed Limiter                                                      Raised

  • Auto Start/Stop Disable

  • MDS Disable

  • Fan for target temp                                           Superchips Value (204 Degrees) / 192 Degrees / 180 Degrees

 

Dashpaq+ (Includes all tune files listed above in Preloaded Tunes)

CLICK HERE TO BUY DASHPAQ+ 30627-S1

 

          Parameter                                              Range (where applicable)

  • Tire Size                                                               25-44″

  • Speed Limiter                                                    40-190 MPH

  • Speed Limiter 4wd Lo                                    47-187 MPH

  • Throttle Booster                                             +1-20%

  • MDS Disable                                                         

  • Idle Speed Adjust                                            -400/+400 RPM

  • Rev Limiter Drive                                             5500-6800 RPM

  • Rev Limiter Neutral                                        -500/+500 RPM

  • Cooling Fan                                                        -10%/+10%

  • WOT Fuel 1-7k                                                   -20/+20%

  • WOT MBT Spark 1-7k                                     -10/+10 degrees

  • WOT Spark 1-7k                                                -10/+10 degrees

  • Auto Start/Stop Disable

  • Traction Control Disable

 

Important Notes:

  • Gateway Bypass Module (included in all kits listed for this application) must be installed while any adjustment or tuning is performed on this vehicle.

  • A PCM swap is required with all 2015+ Dodge/Ram vehicles for tuning, and is included in kits 30627-S1 and 3846-S1.

  • Once you receive your Dashpaq+ or Flashpaq kit, just SUBMIT THIS FORM for an unlocked PCM

Now Tuning 2022 Mustang 5.0

Dashpaq+ and Flashpaq are available now for 2022 5.0L Mustang with peak gains of 20hp/38tq! 

With the preloaded tunes available in either programmer and no other modifications, drivability, midrange power, and throttle response will all improve drastically.  Automatic and manual transmission vehicles are supported by both products.

Transmission calibration from the factory leaves a lot on the table when it comes to the needs of the average enthusiast, and Superchips has enhanced every facet, delivering power to the ground at the driver’s will.  Restrictive torque management functions and other “nanny” contingencies are all but bypassed entirely to put the driver in full control.    

Tune File Name                            Octane           HP              TQ

93 Performance                                       93        20            38

91 Performance                                       91        15            30

                         Modified Stock*                       Stock HP/TQ, allows user adjustments

                        *Dashpaq+ only

 

 

Dashpaq+ for Mustang

Dashpaq+ is state-of-the-art, combining engine monitoring with powerful tuning and a healthy menu of optional user adjustments. Controls are through a simple, high-resolution, touchscreen interface, and updates are easy to apply through wi-fi or your computer.   The added ability to monitor and datalog with dozens of available PID’s makes it the true enthusiast’s device of choice.

 

CLICK HERE TO SHOP FOR DASHPAQ+ #10601

User Adjustments with Dashpaq+

        • Cooling fan, adjustable by target coolant temp, range 180-230 degrees
        • MAF Sensor curve (-20% – +30%)
        • Rev limiter, in Neutral, adjust 3000-9000 RPM
        • Rev limiter, in Gear – (3000-9000 rpm)
        • Cam Timing, adjusts Intake and Exhaust +/-20%, in high and/or low RPM ranges
        • Transmission Shift Points by MPH, each upshift from 1-8th gear by +/-20%
        • Global Spark Advance, +/-10 degrees over stock or selected tune
        • Fuel Table from 2000-4000 RPM, richen or lean by 40%
        • Fuel Table from 4000-7000 RPM, richen or lean by 40%

 

Flashpaq: Performance Upgrade to Your Ford Mustang

 For a more budget friendly option, the Flashpaq handheld tuner offers the same performance gains in a simpler plug and play device containing the ability to apply adjustments and read/clear diagnostic trouble codes. 

User Adjustments with Flashpaq 

        • Rev Limiter, Raise
        • Speed Limiter, Raise
        • Auto Start-Stop Disable
        • Fan Temp- Pre-set Lowered temp. table
        • Global Spark Advance- +/- in degrees
        • Transmission shift strategies for automatics- optimized in existing tunes

 

CLICK HERE to shop for Flashpaq #1845

 

Instant Throttle Response on your Mustang with Amp’D 2.0

Superchips Amp’d 2.0L Throttle Sensitivity Booster is easy to install and delivers immediate improvement to the engine’s throttle response. This increased sensitivity optimizes your Mustang’s driving experience and puts power to the ground when you want it!  Amp’d 2.0 offers an elegantly simple solution that generates “seat of the pants” response you won’t find anywhere else.

Amp’d 2.0 (5) preset throttle settings that can be switched on the fly, and an intuitive plug-and-play installation to factory connectors without cutting or splicing wires.  Settings are adjustable through our wireless switch, or the all-new Amp’d 2.0 smartphone app which includes an option to create custom pedal map curves.

CLICK HERE to shop for Amp’S 2.0 #18862-2

Ford Bronco Sport Tuning

Easy Performance for Ford Bronco Sport 2.0L

Flashpaq #1845

Superchips offers the simplest and most cost-effective solution to your need for added power in the Ford Bronco Sport 2.0L with our latest addition to Flashpaq’s tuning support. With the ability to add up to 36 HP and 42 ft-lb torque on 93 octane fuel*, the Flashpaq has been specifically calibrated to enhance the driving experience in a vehicle with no further modifications.  See the “Preloaded Tunes” list below for details. 

Whether you’re hitting a trail off-road, looking for better fuel mileage on your daily commute, or simply need a boost to all-out acceleration and performance, Flashpaq has you covered. The device also comes preloaded with performance tunes for 91/93 and 87 octane fuel, our Mileage XS and Crawl Tunes, and a host of additional options to re-calibrate for tire size, disable Auto Start/Stop, and much more.

*Engine tuning currently available for 2.0T engines only.

Optional Controls with Tuning- Flashpaq #1845:

  • Rev Limiter: Stock/Pre-set Raised
  • Speed Limiter: Stock/Pre-set Raised
  • Auto Start-Stop: Enable/Disable
  • Fan Temp: Stock/Pre-set Lowered
  • Global Spark Advance: Selectable to +/- in degrees

Quick Options (changes that can be made without reloading a tune)- Flashpaq 1845 and Flashcal 1545:

  • Auto Lights Display: Selects the duration of time the headlights stay illuminated after the driver exits, for 0, 5, 10, 20, 60, or 120 seconds.
  • Auto Lock Disable/Enable: The F-150 will automatically lock its doors when the vehicle reaches about 15 mph.  Flashpaq can turn this off so it will wait until manually triggered by the driver.
  • Remote Unlock All Doors/Driver Door: Choose whether the first press of the unlock button on the key FOB unlocks all doors or driver only.
  • Remote Start Duration: Adjusts vehicle running time after activation with optional durations of 0, 5, 10, and 15 mins.
  • TPMS System Disable: TPMS can be turned off altogether for switching to aftermarket wheels without sensors.  System can also be reenabled at any time with Flashcal.
  • Independent TPMS threshold: With TPMS enabled, the front and rear axles can be set to different warning thresholds, from 1– 90 psi.
  • Tire Size: The enter the measured height in inches, in a range of 25.25 – 29.75” for an accurate speedometer reading after changing to taller or shorter rubber, and the rest of the calculations are done for you.

 *Recalibration of speedometer with gear ratio change is not required on this application.

CLICK HERE TO BUY FLASHPAQ 1845 NOW

Speedometer Calibration (and more!) for Bronco Sport 2.0L & 1.5L

Flashcal #1545

Tire and wheel upgrades are common with trucks and SUVs in general, and Superchips offers the easiest, most cost-effective solution for Bronco Sport owners to correct a speedometer reading for changes to tire height and many other parameters.  In minutes, the Flashcal plugs into the truck’s diagnostic port and the user only has to input their new tire size and/or gear ratio changes to return the speedometer to an accurate calibration.  You’ll rest assured the speedometer and odometer are displaying accurately to keep your time on the highway safe and legal!

In addition to speedometer calibration, Flashcal also offers numerous customizations to your vehicle’s features that were not previously available to the end user.

  • See Quick Options list above for available Flashcal controls

CLICK HERE TO BUY NOW FLASHCAL 1545 NOW

Live Data Monitoring and Added Power for the 2.0L Engine

Dashpaq+ #10601

CLICK HERE FOR DETAILED INFO ON DASHPAQ+

Power:  If you’re looking for tuning and monitoring, the Dashpaq+ is Superchips’ most versatile and feature rich device.  Like Flashpaq, Dashpaq+ opens the option to enhance peak engine power by 36 horsepower and 42 lb.-ft of torque with 93 octane fuel, and in addition contains performance tunes for 91 and 87 octane fuel, a tune to optimize mileage, and a crawl tune for real off-roading*.

Customizable Options:  The preloaded tunes are ready to go as they come on the device, but Dashpaq+ offers a comprehensive menu of other changes that can be made in the process of loading one.  See “Optional Controls” list in this section below.

Monitoring: Dashpaq+ uses a 5″ high-definition screen boasts a high refresh rate ensuring smooth animation for the customizable virtual gauge display.

Easy Updating: The recommended software for updating is available for a Windows or Mac computer, but contains Wi-Fi capability when one is not available.

Multi-License Option: Finally, but certainly not insignificantly, is the option to add additional vehicle licenses and its compatibility with custom tuning.  New vehicle license(s) create additional “parking spaces” in the device’s memory to tune more than one vehicle simultaneously.

Custom Tuning Available*: For modifications that require calibration beyond the Dashpaq+’s abilities out of the box, the device can be loaded with load custom files created by dealers equipped with our sister company’s tuning software, Diablosport CMR.

*Engine tuning currently available for 2.0T engines only.  

Optional Controls with Tuning on Dashpaq+ 10601 on 2.0L engines:

  • Fuel Table from 1-3000 RPM -40% +40%
  • Fuel Table from 3-6000 RPM -40% +40%
  • Global Spark Advance -10 to +10 degrees from stock
  • Cooling Fan -10 to +10 degrees from stock
  • Rev Limiter Neutral, raised 3000-8000 RPM
  • Rev Limiter in Gear raised, 3000-8000 RPM
  • Idle in Drive, set to 400-1200 RPM
  • Idle in Neutral, set to 400-1200 RPM
  • Vehicle Speed Governor On or Off
  • Auto Start/Stop On or Off
  • Tire Size: Height in inches, in a range of 25.25 – 29.75” 

CLICK HERE TO BUY NOW DASHPAQ+ 10601

Preloaded Tunes in Flashpaq 1845 and Dashpaq+ #10601 for 2.0L

Tune Name                                                                                                   HP     Trq.

93 Performance                                                                                          36          42

Performance                                                                                                28          34

87 Octane                                                                                                       16          23

Mileage XS (87 octane)                                                                             16          23

Crawl Tune (87 octane)                                                                            16          23

 

Instant Throttle Response on your Bronco Sport with Amp’d 2.0

Amp’d 2.0 #18862-2

A frequent inquiry we get in the field is how to reduce or eliminate the lag in pedal response after certain modifications, like bigger tires.  This can often be a complaint with completely unmodified SUVs and trucks!

Superchips Amp’d 2.0L Throttle Sensitivity Booster is easy to install and delivers immediate improvement to the engine’s throttle response. This increased sensitivity optimizes your Bronco Sport’s driving experience and reduces spool-up time of the turbo!  Amp’d 2.0 offers an elegantly simple solution that generates “seat of the pants” response you won’t find anywhere else.

Amp’d 2.0 features (5) preset throttle settings that can be switched on the fly, and an intuitive plug-and-play installation to factory connectors without cutting or splicing wires.  Settings are adjustable through our wireless switch, or the all-new Amp’d 2.0 smartphone app which includes an option to create custom pedal map curves.

Calibrate & Add Instant Throttle Response Together

Amp’D 2.0 + Flashcal for Ford #1545-A2

While Flashpaq and Dashpaq+ do offer tremendous power improvements, some Bronco owners wish to tighten up pedal response and recalibrate specific accessories without completely reprograming the engine control. Combining an Amp’d 2.0 Throttle Booster and Flashcal will fill that void, for a relatively small output of money and time.

The combination of Flashcal and Amp’D 2.0 Throttle Booster make for an easy install, and reward on investment that few other modifications can match.

CLICK HERE TO BUY NOW

 

Flashcal’s Making Progress with 2022 Ford F150

CLICK HERE TO BUY NOW

To keep the momentum going from 2021, we just added 2022 F-150 to the Flashcal#1545, and the new configuration from Ford means we have numerous optional controls for it that were not possible on the earlier generation of F-150.

Flashcal’s All New Features and Options for 2021-2022 Ford F-150: 

  • Auto Start/Stop: Disables the Auto S/S and keeps it off every time you restart the vehicle after that, and can be re-enabled any time with the Flashcal.
  • Enable fog light “Bambi Mode”: Simultaneous use of fog lights with high-beams.
  • Honk Warning: Disables the 2-honk warning when driver exits a running vehicle with the key fob in-hand.
  • Enable “Police Dark Car”: Turns off most cabin and exterior lights when the door is opened. This feature is often desired by hunters and campers.
  • Daytime Running Lights: Enables or disables the daytime running lights, without having to navigate the Ford SYNC® menus.
  • Auto Lights Display: Selects the duration of time the headlights stay illuminated after the driver exits, for 0, 5, 10, 20, 60, or 120 seconds.
  • Auto Lock Disable/Enable: The F-150 will automatically lock its doors when the vehicle reaches about 15 mph.  Flashcal can turn this off so it will wait until manually triggered by the driver.
  • Remote Unlock All Doors/Driver Door: Choose whether the first press of the unlock button on the key FOB unlocks all doors or driver only.
  • Remote Start Duration: Adjusts vehicle running time after activation with optional durations of 0, 5, 10, and 15 mins.

Also Contains Flashcal’s Classic Features: 

  • Axle Ratio: Calibrates vehicle speedometer for changes in axle ratios of 3.15, 3.31, 3.55, 3.73, 4.10, and 4.56.
  • TPMS System Disable: TPMS can be turned off altogether for switching to aftermarket wheels without sensors.  System can also be reenabled at any time with Flashcal.
  • Independent TPMS threshold: With TPMS enabled, the front and rear axles can be set to different warning thresholds, from 1– 90 psi. 
  • Tire Size: The enter the measured height in inches, in a range of 28” – 40” for an accurate speedometer reading after changing to taller or shorter rubber, and the rest of the calculations are done for you.

Order Flashcal #1545